|
Specifies the type of the Hovmøller diagram to be produced. Options are:
Specifies the coordinates of a transect line along which the Hovmøller diagram is calculated. Enter the coordinates (lat/long) of a line separated by a "/" (lat1/long1/lat2/long2). Alternatively, use the coordinate assist button.
Specifies the coordinates of the area over which the Hovmøller diagram is calculated. Enter the coordinates (lat/long) of an area separated by a "/" (top left lat and long, bottom right lat and long). Alternatively, use the coordinate assist button.
Specifies the direction along which the averaging of the variable is performed. Options are North South and East West. For North South, the averaging is weighted by cos(latitude).
Specifies the direction of the date/time axis. Options are:
Option Automatic Forwards has the same effect as option User with default Date Min and Date Max.
Specifies the horizontal date minimum value. Default value AUTOMATIC indicates that the minimum value will be taken from the input data.
Specifies the horizontal date maximum value. Default value AUTOMATIC indicates that the maximum value will be taken from the input data.
Specifies the vertical lower limit value, as a pressure level (hPa) or model level (η levels).
Specifies the vertical upper limit value, as a pressure level (hPa) or model level (η levels).
By default, the definition of the vertical and horizontal axes of the Hovmøller diagrams follows pre-defined rules. However, if Swap Axes is set to Yes then the axes will be swapped around.
Used to interpolate the data onto a regular grid, and applies to both the horizontal and vertical axes where appropriate. This parameter is essential for creating a Hovmøller diagram from satellite data.
Specifies the characteristics of the time-series axis to be used in the plotting of the data. Only an Axis Plotting icon can be dropped here. The following axis parameters are defined by the application; therefore, users should not change their values directly: Axis Type (set to Date), Axis Date Min Value and Axis Date Max Value (set according to the above parameters Date Min and Date Max, respectively), and Axis Orientation.
The Axis Orientation parameter is defined according to the following rules:
a) if the selected input pane is Line Hovm, the value is set to Horizontal;
b) if the selected input pane is Area Hovm and the Average Direction is East West, the value is set to Horizontal
c) if the selected input pane is Area Hovm and the Average Direction is North South, the value is set to Vertical.
d) if the selected input pane is Vertical Hovm, the value is set to Horizontal.
However, it is possible to change the Axis Orientation value from its calculated default by setting parameter Swap Axes to Yes. This option is not available for Vertical Hovm.
Specifies the characteristics of the geographical axis to be used in the plotting of the data. Only an Axis Plotting icon can be dropped here. The following axis parameters are defined by the application; therefore, users should not change their values directly: Axis Min Value and Axis Max Value (set according to the values given by parameters Line or Area), Axis Type, Axis Tick Label Type and Axis Orientation. The Axis Type and Axis Tick Label Type parameters are defined according to the following rules:
a) if the selected input pane is Line Hovm, the Axis Type value is set to Geoline.
b) if the selected input pane is Area Hovm and the Average Direction is East West, the Axis Type value is set to Regular and Axis Tick Label Type to Latitude.
c) if the selected input pane is Area Hovm and the Average Direction is North South, the Axis Type value is set to Regular and Axis Tick Label Type to Longitude.
Moreover, the Axis Orientation parameter is defined according to the following rules:
a) if the selected input pane is Line Hovm, the value is set to Vertical
b) if the selected input pane is Area Hovm and the Average Direction is East West, the value is set to Vertical
c) if the selected input pane is Area Hovm and the Average Direction is North South, the value is set to Horizontal.
However, it is possible to change the Axis Orientation value from its calculated default by setting parameter Swap Axes to Yes.
Specifies the characteristics of the level-series axis to be used in the plotting of the data. Only an Axis Plotting icon can be dropped here. The following axis parameters are defined by the application; therefore, users should not change their values directly: Axis Min Value and Axis Max Value (set according to the input data set), Axis Type, Axis Tick Label Type and Axis Orientation.
Specifies if a conversion from model level to pressure level needs to be performed. Options are As In Data and Pressure, If the conversion to pressure is selected and the input data is specified in model levels, the LNSP field should be added to the input data.
Specifies the type of vertical axis - Linear or Logarithmic.