...
Excerpt | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
PreparationsFirst start Metview; at ECMWF, the command to use is The icons you will work with are already prepared for you - please download the following file:
You should now (after a few seconds) see a flexpart_tutorial folder. Please open it up. The input dataThe input data is already prepared for you and is located in folder 'Data'. You will find a FLEXPART Prepare -old icon that was used to generate the data in folder 'Prepare'. The corresponding macro code can also be found there. You do not need to run the data preparation. However, if you wish to do so please note that it requires MARS access and you must set the Output Path parameter accordingly. |
Tutorials
Children Display |
---|
A forward simulation
Enter folder 'fwd'.
We will run FLEXPART to simulate a volcano eruption by releasing of some SO2 from the Icelandic volcano Eyjafjallajökull.
Running the simulation
The simulation is defined by the 'fwd_conc' FLEXPART Run icon and the 'rel_volcano' FLEXPART Release icon, respectively. Both these are encompassed in a single macro called 'fw_cond.mv'. For simplicity will use this macro to examine the settings in detail.
The macro starts with defining the release like this:
Code Block | ||
---|---|---|
| ||
rel_volcano = flexpart_release(
name : "VOLCANO",
starting_date : 0,
starting_time : 15,
ending_date : 2,
ending_time : 12,
area : [63.63,-19.6,63.63,-19.6],
top_level : 9000,
bottom_level : 1651,
particle_count : 10000,
masses : 1000000
) |
This says that the release will happen over a 45 h period between heights 1651 and 10000 m at the location of the volcano and we will release 1000 tons of material in total.
Info |
---|
Please note that
|
The actual simulation is carried out by calling flexpart_run()
:
Code Block | ||
---|---|---|
| ||
#Run flexpart (asynchronous call!)
r = flexpart_run(
output_path : "result_fwd_conc",
input_path : "../data",
starting_date : 20120517,
starting_time : 12,
ending_date : 20120519,
ending_time : 12,
output_field_type: "concentration",
output_flux : "on",
output_trajectory : "on",
output_area : [40,-25,66,10],
output_grid : [0.25,0.25],
output_levels : [500,1000,2000,3000,4000,5000,7500,10000,15000],
release_species : 8,
receptors : "on",
receptor_names : ["rec1","rec2"],
receptor_latitudes : [60,56.9],
receptor_longitudes : [6.43,-3.5],
releases : rel_volcano
)
print(r) |
Here we defined both the input and output path and specified the simulation period, the output grid and levels as well. We also told FLEXPART to generate gridded concentration fields and plume trajectories on output..
Info |
---|
The actual species that will be released is defined as an integer number (for details about using the species see here). With the default species settings number 8 stands for SO2. |
If we run this macro (or alternatively right-click execute
the FLEXPART Run icon) the results (after a minute or so) will be available in folder 'result_fw_conc' . The computations were actually taken place in a temporary folder then metview copied the results to the output folder. If we open this older we will see two files there:
- conc_s001.grib is GRIB file containing the gridded concentration fields
- tr_r1.csv is CSV file containing the plume trajectories
Please note that these are not the original outputs form FLEXTRA but were converted to formats more suitable for use in Metview. For details about the FLEXPART outputs please click here.
Visualising gridded fields
To plot a particular parameter and level we need to filter the desired dataset from the resulting FLEXPART output file. Unfortunately, Metview's Grib Filter icon cannot handle these files (partly due to the local GRIB definition they use) so we need to use other means to cope with this task. For this reason and also to make FLEXPART output handling easier a set of Metview Macro Library Functions were developed. We will heavily use these functions in the examples below.
Inspecting the FLEXPART GRIB file
Before seeing the macro code to generate the plot we inspect the file itself we wanted to plot. Double-click on the 'conc_s001.grib' GRIB icon' in folder 'result_fw_conc' to start up the Grib Examiner. We can see that this file only contains "mdc" (=Mass density concentration) fields. We can find out further details about this parameter by setting the Dump mode to Namespace and Namespace to Parameter:
Generating the plot
The macro to visualise the concentration fields on a given level is 'plot_level.mv'.
First, we define the level (8000 m) and the parameter ("mdc") we want to plot. Then we call mvl_flexpart_read_hl() to filter the data into a fieldset.
Code Block |
---|
dIn="result_fwd_conc/"
inFile=dIn & "conc_s001.grib"
lev=8000
par="mdc"
#Read fields on the given height level
g=mvl_flexpart_read_hl(inFile,par,lev,-1,-1) |
Next, we define the contouring definition. The units we used here are ng m**-3 because for parameter "mdc" the native units (kg m**-3) are automatically scaled by the plotting library (see details about the this scaling for various FLEXPART GRIB fields here.
Code Block | ||
---|---|---|
| ||
#The contour levels
cont_list=[1,10,50,100,150,200,250,500,750,1000,2000,6000]
#Define contour shading
conc_shade = mcont(
legend : "on",
contour : "off",
contour_level_selection_type : "level_list",
contour_level_list : cont_list,
contour_label : "off",
contour_shade : "on",
contour_shade_method : "area_fill",
contour_shade_max_level_colour : "red",
contour_shade_min_level_colour : "RGB(0.14,0.37,0.86)",
contour_shade_colour_direction : "clockwise",
contour_method: "linear"
) |
Next, we build the title with mvl_flexpart_title(). Please note that we need to explicitly specify the plotting units!
Code Block | ||
---|---|---|
| ||
title=mvl_flexpart_title(g,0.3,"ng m**-3") |
Finally we define the view with the map:
Code Block | ||||||
---|---|---|---|---|---|---|
| ||||||
#Define coastlines
coast_grey = mcoast(
map_coastline_thickness : 2,
map_coastline_land_shade : "on",
map_coastline_land_shade_colour : "grey",
map_coastline_sea_shade : "on",
map_coastline_sea_shade_colour : "RGB(0.89,0.89,0.89)",
map_boundaries : "on",
map_boundaries_colour : "black",
map_grid_latitude_increment : 5,
map_grid_longitude_increment : 5
)
#Define geo view
view = geoview(
map_area_definition : "corners",
area : [40,-25,66,9],
coastlines: coast_grey
) |
and generate the plot:
Code Block | ||
---|---|---|
| ||
plot(view,g,conc_shade,title) |
Having run the we get a plot like this (after navigating to step 39h):
Code Block |
---|
#Metview Macro
# **************************** LICENSE START ***********************************
#
# Copyright 2017 ECMWF. This software is distributed under the terms
# of the Apache License version 2.0. In applying this license, ECMWF does not
# waive the privileges and immunities granted to it by virtue of its status as
# an Intergovernmental Organization or submit itself to any jurisdiction.
#
# ***************************** LICENSE END ************************************
dIn="result_fwd_conc/"
inFile=dIn & "conc_s001.grib"
lev=8000
par="mdc"
#Read fields on the given height level
g=mvl_flexpart_read_hl(inFile,par,lev,-1,-1)
#The countour levels
cont_list=[1,10,50,100,150,200,250,500,750,1000,2000,6000]
#Define contour shading
conc_shade = mcont(
legend : "on",
contour : "off",
contour_level_selection_type : "level_list",
contour_level_list : cont_list,
contour_label : "off",
contour_shade : "on",
contour_shade_method : "area_fill",
contour_shade_max_level_colour : "red",
contour_shade_min_level_colour : "RGB(0.14,0.37,0.86)",
contour_shade_colour_direction : "clockwise",
contour_method: "linear"
)
#Define coastlines
coast_grey = mcoast(
map_coastline_thickness : 2,
map_coastline_land_shade : "on",
map_coastline_land_shade_colour : "grey",
map_coastline_sea_shade : "on",
map_coastline_sea_shade_colour : "RGB(0.89,0.89,0.89)",
map_boundaries : "on",
map_boundaries_colour : "black",
map_grid_latitude_increment : 5,
map_grid_longitude_increment : 5
)
#Define geo view
view = geoview(
map_area_definition : "corners",
area : [40,-25,66,9],
coastlines: coast_grey
)
#Title
title=mvl_flexpart_title(g,0.3,"ng m**-3")
plot(view,g,conc_shade,title) |
Please look into the visualisation macros to see how to use them. The most important Metview Macro Library Functions are as follows:
...
mvl_flexpart_read_hl(inFile,par,lev,ts,ac)
# Function to get flexpart fields on height level
# params:
# inFile: input file
# par: parameter shortname
# lev: level (-
1
means all)
# ts: step (-
1
means all)
# ac: ageclass (-
1
means all)
...
mvl_flexpart_read_sfc(inFile,par,ts,ac)
# Function to get surface flexpart fields
# params:
# inFile: input file
# par: parameter shortname
# ts: step (-
1
means all)
# ac: ageclass (-
1
means all)
|
|
Forward simultaions
Fields
Trajecories
receprotros
volume fill
fluxes
cross section
time-height diagram
total column
age class
backward simulation
residence time
fluxes
trajecory